德國進口齒輪油泵 進口齒輪油泵廠家 進口齒輪油泵價格gear pumps
德國KAYSEN凱森進口齒輪油泵概述
本系列齒輪泵主要有齒輪、軸、泵體、安全閥、軸端密封所組成。齒輪油泵適用于輸送不含固體顆粒和纖維,無腐蝕性,溫度不高于80℃,粘度為5×10-6~1.5×10-3m2/s (5-00cSt)的潤滑油或性質類似潤滑油的其他液體。
主要特點:
1、齒輪油泵使用規定電壓
線路電壓不超過抽液泵銘牌上所規定電壓的±10%方可使用。
2、齒輪油泵如何裝備
開箱后按結構示意圖裝配,接上電動機
(1)并緊接連電機
(2)使之泵體與電機為一體
(3)上接好出水輪管
3、齒輪油泵使用前檢查各部件外型完好才能開機使用。
4、齒輪油泵不宜作空運轉,使用時,抽吸完畢,即停泵,否則會加速葉輪密封件軸承等磨損。也可能磨損泵管,因本泵電機空載轉速可達10000轉/分。
5、齒輪油泵及時調換電刷,電刷磨損到將不能使用時,須及時調換(2只電刷同時調換)否則會使電刷與換向器接觸不良引起壞損,損壞換向器,嚴重時會燒壞電樞。
6、齒輪油泵在下列情況下不得使用,在使用過程中如發現絕緣損壞,電源線工電纜護套破裂,插頭插座開裂或接觸不良,以及斷續運轉,出現嚴懲火花等故障時,電機外殼操作時,應立即進行修理。在未修復前不得使用。
7、齒輪油泵防止過載,使用時,凡遇轉速異?;蚪档蜁r(shí),應即停機檢查是否有雜物卡住葉輪或電機是否發生故障,抽液泵因故剎車時必須立即切斷電源
8、齒輪油泵使用工具要愛惜,所有抽涂泵要小心輕放避免受到?jīng)_擊。
主要優點:
●齒輪經熱處理有較高的硬度和強度,與軸一同安裝在可更換的軸套內運轉。泵內全部零件的潤滑均在泵工作時利用輸出介質而自動達到。
●泵內有設計合理的泄油和回油槽,是齒輪在工作中承受的扭矩力zui小,因此軸承負荷小,磨損小,泵效率高。
●泵設有安全閥作為超載保護,安全閥的全回流壓力為泵額定排除壓力的1.5倍,也可在允許排出壓力范圍內根據實際需要另外調整。但注意本安全閥不能作減壓閥的*工作,需要時可在管路上另行安裝。 從主軸外端向泵看,為順時針旋轉。
主要應用:
●在輸油系統中可用作傳輸、增壓泵
●在燃油系統中可用作輸送、加壓、噴射的燃油泵
●在一切工業領域中,均可作潤滑油泵用
Germany KAYSEN imported gear pump overview
This series gear pump mainly gears, shaft, pump body, safety valve, shaft seal composed. Gear oil pump is suitable for conveying lubricating oil with no solid particles and fibers, no corrosion, temperature not higher than 80 ℃, viscosity of 5 × 10-6 ~ 1.5 × 10-3m2 / s (5-00cSt) or similar properties Other liquids of oil.
main feature:
1, gear pump using the specified voltage
The line voltage does not exceed ± 10% of the voltage specified on the pump nameplate.
2, gear pump how to equip
Out of the box after the structure of the assembly diagram, connected to the motor
(1) and immediay connected to the motor
(2) so that the pump body and the motor as a whole
(3) connected to a good water tube
3, gear pump before using the components to check the appearance of good start to use.
4, gear pump should not be empty operation, use, suction is completed, that is, stop the pump, otherwise it will accelerate the impeller seal bearing wear. May also wear pump tubing, because the pump motor no-load speed up to 10,000 r / min.
5, the gear pump timely exchange brush, brush wear will not be able to use, it is necessary to timely exchange (2 brush at the same time exchange) otherwise the brush and commutator bad contact caused damage, damage commutator, serious Will burn the armature.
6, the gear pump in the following circumstances shall not be used in the course of the use of insulation damage, power cord cable sheath rupture, plug socket cracking or poor contact, and intermittent operation, severe sparks and other failures, the motor shell operation Should be repaired immediay. Do not use before repair.
7, gear pump to prevent overload, when used, when the speed is abnormal or reduced, it should be shut down to check whether there is debris stuck impeller or motor failure, pumping pump brake must immediay cut off the power
8, gear pump use tools to cherish, all pumping pump to be careful to avoid the impact.
Key Benefits:
● The gears have a high hardness and strength by heat treatment and are installed in the replaceable sleeve with the shaft. All parts of the pump lubrication in the pump work with the output medium and automatically reached.
● The pump has a reasonable design of the drain and oil return tank, the gear in the work to withstand the minimum torque force, so the bearing load is small, wear small, high pump efficiency.
● The pump is equipped with a safety valve as overload protection. The full return pressure of the safety valve is 1.5 times of the rated pressure of the pump. It can also be adjusted according to the actual requirement in the allowable discharge pressure range. But pay attention to the safety valve can not be the long-term work of the valve, if necessary, can be installed on the pipeline. From the outer end of the spindle to the pump, for the clockwise rotation.
main application:
● In the oil system can be used as transmission, booster pump
● Fuel pump can be used in the fuel system for conveying, pressurizing and spraying
● In all industrial areas, can be used for lubricating oil pump
德國進口齒輪油泵 進口齒輪油泵廠家 進口齒輪油泵價格
德國KAYSEN凱森對您的承諾:
●放心的質量:從鑄件到產品,實行全過程質量監控,*檢測,責任到人!
●貼心的價格:高效成本控制,自產自銷,減少中間環節,讓利于客戶!
●快速的貨期:充足的庫存,上海便捷物流,縮短交貨期,嚴格按照合同期交貨!
Germany Kaysen commitment to you:
● Reliable quality: from casting to the product, the implementation of the whole process of quality control, all-round detection, responsibility to the people!
● intimate price: efficient cost control, production for sale, to reduce the intermediate links, to help customers!
● fast delivery: adequate inventory, Shanghai convenient logistics, shorten the delivery time, in strict accordance with the contract delivery!
進口齒輪油泵廠家 進口齒輪油泵價格