進口水循環真空泵｜美國進口水循環真空泵

進口水循環真空泵｜美國進口水循環真空泵

進口水循環真空泵概述：

在水環泵中，輔助排氣閥是一種特殊結構，一般采用橡皮球閥，它的作用是消除泵在運轉過程中產生的過壓縮與壓縮不足的現象。這兩種現象都會引起過多的功率消耗。因?yàn)樗h(huán)泵沒有直接的排氣閥，而且排氣壓力始終是固定的，水環泵的壓縮比決定于進氣口的終止位置和排氣口的起始位置，然而這兩個位置是固定不變的，因而不適應吸入壓力變化的需要。為了解決這個問題，一般在排氣口下方設置橡皮球閥，以便當泵腔內過早達到排氣壓力時，球閥自動開啟，氣體排出，消除了過壓縮現象。一般在設計水環泵時都以zui低吸入壓力來確定壓縮比，以此來確定排氣口的起始位置，這樣就解決了壓縮不足的現象。

進口水循環真空泵工作原理：

循環水真空泵的工作水與被壓縮氣體是一起排出的．因此水環需用新的冷水連續補充．以保持穩定的水環厚度和溫度。水環除起“液體活塞”作用．還有散熱(對縮壓過程)密封(葉輪與配氣板之間)冷卻(軸封件)等作用。因此泵的工作轉速(對應一定的水環厚度)實際工作水溫和配氣孔布置是幾個主要影響因素．對抽氣量、工作效率和壓縮比(包括可達真空度)起決定性作用。

進口水循環真空泵技術參數：

抽氣量：230-23850m3/h 口徑：50-500mm
吸入絕壓：33mbar，160mbar
轉速：210-1750r/min 電機功率：11-560kw
產品標準：Q/FP201.1-201.3-89(epv DIN28431)
傳動方式：聯軸器傳動、皮帶傳動

進口水循環真空泵美國泰樂TYLER售后服務：

*的服務鑄就*的企業讓客戶無后顧之憂。
1、按合同要求提供產品的合格證、銘牌、檢驗報告、產地證名、安裝說明書等。
2、顧客在驗收產品過程中，如出現與合同要求不符時，我司接到顧客通知后兩小時內給予處理。
3、我司提供十二個月以上產品質保期，時間從驗收合格之日起計算。
4、在正確安裝和使用下，出現產品質量問題，本公司將負責到底。

Import water circulation vacuum pump imported water circulation vacuum pump

Introduction of imported water circulation vacuum pump:

In the water ring pump, auxiliary exhaust valve is a special structure, the general use of rubber ball valve, which is to eliminate the role of the pump in the process of excessive compression and compression phenomenon. These two phenomena will cause excessive power consumption. Because the water ring pump no exhaust valve directly, and exhaust pressure is always fixed, the compression ratio of the water ring pump depends on the termination of the inlet and outlet position of the starting position, but the two positions are fixed, and therefore does not meet the need of the suction pressure change. In order to solve this problem, the general set of rubber ball valve at the bottom of the exhaust valve, so that when the pump cavity to achieve premature exhaust pressure, the ball valve automatically open, gas discharge, eliminating the phenomenon of over compression. Generally in the design of water ring pump with the lowest suction pressure to determine the compression ratio, in order to determine the starting position of the exhaust port, so that the phenomenon of compression is solved.

Working principle of inlet water circulation vacuum pump:

The working water of the circulating water vacuum pump is discharged together with the compressed gas, so the water ring needs to be continuously replenished by new cold water. In addition to the "water ring liquid piston effect. There are heat (the compression process) (seal between the impeller and the air distributing plate (cooling) seal pieces) etc.. Therefore, the pump speed (corresponding to a certain thickness of the water ring) working temperature and distribution hole layout is the main influence factors. On the content, work efficiency and compression ratio (including to vacuum) play a decisive role.

Technical parameters of imported water circulation vacuum pump:

Exhaust gas: 230-23850m3/h diameter: 50-500mm

Suction pressure: 33mbar, 160mbar

Speed: 210-1750r/min motor power: 11-560kw

Product standard: Q/FP201.1-201.3-89 (EPV DIN28431)

Transmission: coupling drive, belt drive

The United States imported water circulation pump TYLER Taylor customer service service:

The first-class service created a first-class enterprise so that customers no worries.

1, according to the contract requirements for product certification, nameplate, inspection report, certificate of origin, installation instructions etc..

2, the customer in the process of acceptance of the product, such as the emergence of the contract requirements and inconsistent, I received the notification of the customer within two hours after the treatment.

3, our company provides more than twelve months warranty period, the time from the date of acceptance.

4, in the correct installation and use, product quality problems, the company will be responsible in the end.